Product information

Enclosure Water Resistance ​Rain Environmental Test Chamber

If you are interested in this product, you can
product name: Enclosure Water Resistance ​Rain Environmental Test Chamber
product number: LY-L80
Exhibitors: LIYI
Product Documentation: No Related Documents

a brief introdction

Enclosure Water Resistance Rain Environmental Test Chamber Can manual default the test parameters, complete testing automatically shut off the water supply and pendulum pipe Angle automatic zeroing and automatic eliminate seeper, avoid scale blockage needle tip. Enclosure Water Resistance Rain Environmental Test Chamber Use Mitsubishi PLC, LCD panel test procedure control box.


Enclosure Water Resistance ​Rain Environmental Test Chamber  Detailed description

Enclosure Water Resistance Rain Environmental Test Chamber

 

PX1/2 Vertical Rain Drop Test 
1.  Meet the requirement of IEC60529 standard IPX1 vertical rain drop test and IPX2 15°inclination rain drop test.

 

2.  Rainfull capacity:  IPX1: 1 ±0.5mm/min
                                  IPX2 : 3 ±0.5mm/min

 

3.  Water drop chamber effective dripping area: 1000*1000mm, water droping hole diameter: Φ0.4mm, hole distance: 20*20mm

 

4.  Water drop chamber uses vaccum design, match with oxidation alloy aluminium and high rust stainless steel material structure, nozzle contact a brass tapered design, convenient in installation and replace needle tip.

 

5.  Rain drop device can automatically lift, nozzle is located in 200mm from the highest point of test sample, and equipped with protection devices to ensure it would not drop too fast. It can also lift manually.

 

6.  With compressed air dry function, when the experiment is complete but will drop out the excess water clean, avoid long time water dirty jams needle tip.

 

7.  Dc electric lifting motor drive, stainless steel wire rod, pulley guide with locking nut lifting device.

 

8.  Aluminum alloy and stainless steel fuselage; Hang to the wall or four column equality lifting.

 

 

IPX3/4 Vertical Rain Drop Test 
1.  Enclosure Water Resistance Rain Environmental Test Chamber Meet the requirement of IEC60529 standard IPX3 water pouring test and IPX4 water splash test.

 

2.  The test sample will be put or installed on the center of the half-round sinuous pipe and make the bottom of the test samples and the oscillating axis in a horizontal position. During test, the sample would spin around the center line.

 

3.  Swing pipe standard configuration: R600mm and R1000mm two types.  

     Swing pipe inner diameter: Φ15mm.       
     DillΦ0.4 holes and make the water spray to the center.  

     The water pressure of the device entrance is equal to 10m water level, spraying water pressure is 80-100kpa.

 

4.  Water spraying pipe swing angle: 120º,180º,360º,  Vertical sides: 60º,90º,175º.
     Complete a swing(2*120º) time is 4S.
     Complete a swing(2*360º) time is 12S.

 

5. Enclosure Water Resistance Rain Environmental Test Chamber Can manual default the test parameters, complete testing automatically shut off the water supply and pendulum pipe Angle automatic zeroing and automatic eliminate seeper, avoid scale blockage needle tip.

 

6.  Enclosure Water Resistance Rain Environmental Test Chamber Use Mitsubishi PLC, LCD panel test procedure control box, stainless steel curved pipe, alloy aluminum frame, stainless steel shell.

 

7.  Servo drive mechanism, guarantee the pendulum pipe Angle of precision, the overall pendulum tube structure for hang a wall.

 

Pendulum tube radiusmm

IPX3

IPX4

Blowhole number

Total Flow

Blowhole number

Total Flow

L/min

L/h

L/min

L/h

400/500

25

1.8

108

37

2.6

156

 

 

Rain Environmental Test Chamber for Enclosure Water Resistance Test

Enclosure Water Resistance Rain Environmental Test Chamber

Leave a message for product
Title
Contact
Tel
Content
Verify Code
Click to change
Note:1. Shortcut key for send message :Alt+s or Ctrl+Enter!
2. If necessary, please leave your detail contact!